Banner L-GAGE LT7PIDQ Manual Download Page 19

L-GAGE

®

 LT7 Long-Range Time-of-Flight Sensor

P/N 120244   

19

Banner Engineering Corp. 

• 

Minneapolis, MN U.S.A.

www.bannerengineering.com  •  Tel: 763.544.3164

Specifications, cont’d 

Description of Laser Classes

Class 2 (Visible Pilot Laser)

Lasers that emit visible radiation in the 

wavelength range from 400 nm to 700 nm 

where eye protection is normally afforded 

by aversion responses, including the blink 

reflex. This reaction may be expected to 

provide adequate protection under 

reasonably foreseeable conditions of 

operation, including the use of optical 

instruments for intrabeam viewing.

Reference 60825-1 Amend. 2 © 

IEC:2001(E), section 8.2.

Class 1 (Infrared Sensing Laser)

Lasers that are safe under reasonably 

foreseeable conditions of operation, 

including the use of optical instruments for 

intrabeam viewing.

Reference 60825-1 Amend. 2 © 

IEC:2001(E), section 8.2.

Operating Mode
Laser Class 1

Setup Mode
Laser Class 2

Do not stare into beam

Storage Temperature

-30° to +75° C (-22° to +167° F) 

Vibration/Shock

EN 60947-5-2 

Application Notes

•  All specifications are based on the specified surface at constant ambient conditions and following a 

minimum operating time of 15 minutes.

• For best accuracy, allow a 15-minute warmup before programming or operating

• 

Crosstalk avoidance: 

Light spots must be separated by at least 200 mm.

• Also see page 12 for target orientation notes.

Certifications

OUTPUT1

OUTPUT2

ALARM

POWER

ESC

Operating Mode
Laser Class 1

Setup Mode
Laser Class 2
Do not stare into beam

(Infrared)

(Visible - Red)

Operating Mode
Laser Class 1

Setup Mode
Laser Class 2
Do not stare into beam

(Infrared)

(Visible - Red)

wh

TX + / SSI: Data +

bn

Output 1 (PNP)

gn

RX + / SSI: Clock + 

ye

Analog Output: 4 - 20mA

gy

Alarm 1 Output (PNP)

pk

Alarm 2 Output (PNP)

rd

18 - 30V dc

bk

RX - / SSI: Clock -  

vt

N/C

gy/pk

TX - / SSI: Data -

rd/bu

Output 2 (PNP)

bu

Gnd 

LT7PIDQ

bannerengineering.com

bannerengineering.com

Class 1

L - GAGE

TM 

wh

TX + / SSI: Data +

bn

Output 1 (PNP)

gn

RX + / SSI: Clock + 

ye

Analog Output: 4 - 20mA

gy

Alarm 1 Output (PNP)

pk

Alarm 2 Output (PNP)

rd

18 - 30V dc

bk

RX - / SSI: Clock -  

vt

N/C

gy/pk

TX - / SSI: Data -

rd/bu

Output 2 (PNP)

bu

Gnd 

LT7PIDQ

bannerengineering.com

bannerengineering.com

Class 1

L - GAGE

TM 

�������

�����

�������

�����

�������

�����

�������

�����

�������

�����

�������

�����

�������

�����

��������

�����

��������

�����

�����������

�������

�����

�������

�����

�������

�����

�������

������������

Dimensions

Summary of Contents for L-GAGE LT7PIDQ

























Reviews: