background image

Accessories  •  USB flash drive

Chapter 5 Accessories

Automation PC 910 User's Manual V 1.00

111

4  USB flash drive

4.1 5MMUSB.2048-01

4.1.1 General information

USB flash drives are storage media that are easy to replace. Because of their fast data transfer (USB 2.0), USB

flash drives are ideal for use as portable data storage. Without requiring additional drivers ("Hot Plug & Play" -

except with Windows 98SE), the USB flash drive can immediately act as an additional drive where data can be

read or written.

Information:

We reserve the right to supply alternative products due to the vast quantity of USB flash drives available

on the market and their corresponding short product lifecycle. Therefore, the following measures might

be necessary in order to boot from these flash drives:

The flash drive must be reformatted or in some cases even re-partitioned (set active partition).

The flash drive must be at the top of the BIOS boot order, or alternatively the IDE controllers can
also be deactivated in the BIOS. This can be avoided in most cases if a "fdisk /mbr" command
is also executed on the USB flash drive.

USB 1.1, USB 2.0

High transfer rate

High data storage

Ambient temperature during operation: 0 to 70°C

4.1.2 Order data

Model number

Short description

Figure

USB accessories

5MMUSB.2048-01

USB 2.0 flash drive 2048 MB B&R

Table 96: 5MMUSB.2048-01 - Order data

4.1.3 Technical data

Product ID

5MMUSB.2048-01

General information

Data retention

> 10 years

LEDs

1 LED (green), signals data transfer (send and receive) 

1)

MTBF

> 3,000,000 hours

Type

USB 1.1, USB 2.0

Maintenance

None

Certification

CE

Yes

Interfaces

USB

Type

USB 1.1, USB 2.0

Connection

To each USB type A interface

Transfer rate

Low speed (1.5 Mbit/s), full speed (12 Mbit/s), to high speed (480 Mbit/s)

Sequential reading

Max. 31 MB/s

Sequential writing

Max. 30 MB/s

Support

Operating systems

Windows 7

Yes

Windows XP Professional

Yes

Windows XP Embedded

Yes

Windows ME

Yes

Windows 2000

Yes

Windows CE 5.0

Yes

Windows CE 4.2

Yes

Electrical characteristics

Power consumption

Max. 500 µA sleep mode, max. 120 mA read/write

Environmental conditions

Temperature

Table 97: 5MMUSB.2048-01 - Technical data

Summary of Contents for Automation PC 910






































































































































































Reviews: