- 16 -
Wireless charging system 600W specification
For 12V・24V・
48V
battery
- 10 -
2-4
車上装置
2-4-1
充電コントローラ
（
1
）ヘッド接続部①②
①
.
受電ヘッド 電力用
3P
コネクタを接続
②
.
受電ヘッド 通信用
5P
コネクタを接続。
（
2
）表示③
表
8
の表示及び表
9
の異常判別を有する。
表
8
充電コントローラ 表示
名称
機能
表示手段
出力
備考
Ready
充電開始信号で表示
青色灯火
有り
Charge
定電流または定電圧充電動作中を表示
燈色灯火
有り
End
充電終了を表示
緑色灯火
有り
Error
異常を表示
赤色灯火
有り
Error code
E1
～
E3
の組合せにより異常内容を表示
赤色灯火
無し
表
9
充電コントローラ 異常判別
名称
検知内容及び原因
LED
表示
E1 E2 E3
充電コントローラ過熱
充電コントローラ内の過熱検知
(
約
85
±
5
℃
)
○
○
電池電圧異常
電池電圧
16-0.5
～
31+0.5V
以外を検知
○
出力過電流
電池への過電流を検知
(25
±
0.5A)
○
電池温度異常
電池の過熱検知
(
約
50
±
5
℃
)
○
出力過電圧
電池への過電圧を検知
(33
±
0.5V)
○
○
通信異常
ヘッドの温度異常、定格ギャップから外れた場合
Name
Function
Pin No. Remark
Power
ON with power supply
4,20
Output
Ready
ON when charging is stopped (charging standby state)
5,20
Output
Charge
ON during constant current or constant voltage charge operation
6,20
Output
End
ON at the end of charging
7,20
Output
Error
ON when abnormal
8,20
Output
E1
E2
E3
The abnormality are indicated by LED lighting combinations of E1 to E3
16,20
17,20
18,20
Output
I/O connector function
Please do not wire with combinations other than those indicated in "I/O connector function" above.
The operation status of the power supply unit is output to the outside simultaneously with the LED indication.
The operation of the output signal turns ON when the LED is lit.
The output circuit is rated voltage 24 V max. current 50 mA, with surge protection only (39 V).
※ The Dsub 25 pin plug side must be prepared separately by the customer.
Soldering type：HDBB-25P (05) Hirose Electric Case made by HDB-CTH Hirose Electric
Terminal block type：SUBCON 25M-SH made by Phoenix Contact
Protective cap：DB-25S-DC1 Hirose Electric
⑤ Mounting section
For housing fixing 7 x 15 (M6 bolts: 4 locations for mounting, 4 locations for auxiliary)
⑥ Power
Single phase power supply (90 to 220 V) is connected by AC inlet, this path has over current protection circuit by fuse.
In addition, please set the grounding resistance to 100 Ω or less.
⑦ Power switch
Turn main power ON / OFF.
⑧ Exhaust port
In order to exhaust internal heat by the fan, consider it so that exhaust heat can dissipate to the outside air, please
install 50 mm or more away from the wall.
⑨ inlet
In order to take in the outside air with the fan, consider it so that air can be taken in from the outside air, please set it apart
50 mm or more from the wall.
● Charging side
(RCS600-CA12)
(RCS600-CA24)
(
RCS600-CA48
)
RCS600
CA
12
RCS600
CA
24
RCS600
CA
48
7
7
14
7
7
14
232
135
80
160
260
16.5
12.5
210
24
1.
6
型式：RCS600-CA24
RCS600
CA
24
Setting
Charge voltabe max.
28.8V
Charge current max.
20.0A
Recharge voltabe
24.0V
※ The printed content of the side label depends on the type code.
Charging unit display（RCS600(B)-CA ＿）
① Passive head
Connect 3P connector for power supply
② Passive head
Connect 5P connector for communication
③ LED display and error indication
Charging unit indication
Name
Function
Display method
Output
Ready
Displayed in the stopped charging state (charging standby state)
Light in Blue
Present
Charge
Displaying during constant current or voltage charge operation Light in Orange
Present
End
Display the end of charging
Light in Green
Present
Error
Indicates abnormality
Light in Red
Present
Error code
Display abnormal contents by combination E1 ～ E3.
Light in Red
Present
For details on how to identify and deal with abnormalities, please refer to “Identifying and Troubleshooting
Abnormalities” on page 28.
Do not wire to pins other
than those listed in “I/O
Connector Functions”.
It may couse malfunction
if wired to pins other than
listed in the table on the
left.
