- 19 -
Wireless charging system 600W specification
For 12V・24V・
48V
battery
BATT
12V
+
-
BATT
12V
+
-
AC 90～220V
受電ヘッド
RCS600-CH-L
給電ヘッド
RCS600-AH-L
電源ユニット
RCS600-AC
■充電ユニット
・RCS600-CA24（24V仕様）
・RCS600-CA12（12V仕様）
・RCS600-CA48（48V仕様）
サーミスタ
※バッテリ数は各仕様による
24V仕様・・・12V x 2(直列）
12V仕様・・・12V x 1
48V仕様・・・12V x 4(直列）
E04SR401938
(フェライトコア)
1T/100mm以内
E04SR401938
(フェライトコア)
100mm以内
フェライトコア付き
電源ケーブル
Dsub25P起動信号ON用
コネクタ
RCS600-OP001
RFC-H13
(フェライトコア)
2T/100mm以内
3T
2T
- 3 -
図 1 全体構成図（標準仕様）
図 2 全体構成図（長距離仕様）
Long distance Specification Head
※ 2
※ 1
※ About installing the Ferrite Clamp
In order to fulfill the criteria of Article 65, paragraph 1, product 3 of the Radio Equipment Regulations, and
Ministry of Internal Affairs and Communications Notification 207, and malfunction preventionplease attach
the enclosed ferrite clamp to the following positions with specified turns each.
Case for standard specification head
· 1piece to the communication cable of the passive head within 100 mm from the charging unit. (2 turns)
· 1piece each to the power supply cable and communication cable of the active head within 100 mm from
the power supply unit. (2 turns)
· 1piece to the power supply cable within 300 mm from the power supply unit. (2 turns)(It is already installed
at the time of shipment)
Case for long distance specification heads (see figure above)
・ 1 piece from the charging unit to the battery within 100 mm (1 turn)
・ 1 piece to the communication cable of the active head within 100 mm from the power supply unit (2 turns)
・For the power cable, attach 1 piece of additional ferrite core clamp included with the active head within
300 mm in addition to the one already installed at the time of shipment. (Refer to the figure above ※ 3)
※ When using each extension cables, install them on the unit side regardless of the head specifications.
Please refer to the next page.
2T
3T
2T
3T
1T
RCS600
CA
12
RCS600
CA
24
RCS600
CA
48
※ 3
2 turns
3 turns
90 ～ 220V AC
(If you want to use it at AC200V, you need to
process the tip)
Power cable with ferrite clamp
（Cable lenth 180cm - Included clamp）
AYCS-212 BK
E04SR401938
( フェライトコアクラン
Ferrite core clamp)
3T&2T/within 300mm
1turn
※ 2 Charging cable is not included.
A cable of 5.5 sq or more is recommended.
Battery depends on each specification
12V type…12V × 1 24V type…12V × 2
(series)
48V type…12V × 4
(series)
Lead battery
or
Lithium Ion Battery
Battery
Thermistor Type code：
RCS600-OP002
E04SR401938
Ferrite clamp
Within 1T/300mm
Charging unit
RCS600(B)-CA12(12V)
RCS600(B)-CA24(24V)
RCS600(B)-CA48(48V)
Dsub25P-Connector for
start signal ON
RCS600-OP001
※ 1 This is a D-sub connector in which PIN1 and PIN14 are
shorted circuit internally. When this connector is attached to
the charging unit, charging starts automatically when the head
is facing. (Required only for normal open type. Not required for
normal close type)
2 turns
1T=1 turn
2T=2 turns
3T=3 turns
RFC-H13
Ferrite core clamp
Within 2T/100mm
Connector for power supply
Connector for
communication
Active Head
RCS600-AH-L
Passive Head
RCS600-CH-L
Power Supply unit
RCS600-AC
