background image

Regulator Display Modes

 - 

Basic Display/Long Display

The regulator’s three digit alphanumeric LED display provides a scrolling view of charging status. Under normal operation, 

the display will indicate the following:

Indicates Max Charge MC-612-DUAL.

Indicates regulator’s default Universal Factory Program. Display will vary based on program selected. 

Indicates the regulator’s Belt Load Manager setting. Ranges from b-0 to b-7.

Indicates stage of charge. “b” indicates bulk. “A” indicates absorption. “F” indicates float.

Indicates “real time” battery system voltage. Followed by actual voltage reading.

Indicates Calculated voltage (target voltage based on preset program levels). Followed by voltage reading.

Indicates Battery #1 temperature. Followed by NC (not connected), or temperature in celsius.

Indicates Alternator #1 temperature. Followed by NC (not connected), or temperature in celsius.

Indicates Battery #2 temperature. Followed by NC (not connected), or temperature in celsius.

Indicates Alternator #2 temperature. Followed by NC (not connected), or temperature in celsius.

* Alt. #2 or Bat. #2 Temperature Sensing are user selectable. One or the other will be shown in the regulator display.

In addition to the information provided in the basic display shown above, the MC-612-DUAL long display provides the fol-

lowing data. The long display is accessed during basic programming, which will be discussed in the next section of the 

manual. 

Indicates the percentage of field output to the alternator. The higher the percentage, the greater the output.

Indicates regulator’s software revision code.

Indicates temperature setpoint for ambient alternator and battery temperatures. Followed by degrees celsius.

Indicates, in millivolts, the voltage value used to control voltage compensation for  battery temperature.

Indicates overall regulator hours. Followed by hours (by tenths) and hours in excess of 100.

Indicates field threshold from bulk to absorption. Factory set at 65%. Adjust in advanced programming mode.

Indicates field threshold from float to absorption. Factory set at 65%.  Adjust in advanced programming mode.

Indicates system advisory codes. Individually numbered codes are defined below.

The following advisory codes can be used to determine possible system errors or to identify specific operational modes. 

Note that E codes are cumulative and will be held in memory until cleared. Codes can be by cycling from LD to SD in the 

basic programming mode, and back to LD after the SD mode has been saved. See basic programming for more info.

BATTERY #1 TEMP. SENSOR 

CABLE SHORTED
BATTERY #1 TEMP. SENSOR 

CABLE OPEN OR NOT FOUND
BATTERY #2 TEMP. SENSOR 

CABLE SHORTED
BATTERY #2 TEMP. SENSOR 

CABLE OPEN OR NOT FOUND
ALTERNATOR #1 TEMP. SENSOR 

CABLE SHORTED
ALTERNATOR #1 TEMP. SENSOR 

CABLE OPEN OR NOT FOUND
ALTERNATOR #2 TEMP. SENSOR 

CABLE SHORTED

ALTERNATOR #2 TEMP. SENSOR 

CABLE OPEN OR NOT FOUND
BATTERY #1 TOO HOT. OVER 

52˚C. FACTORY DEFAULT
BATTERY #2 TOO HOT. OVER 

52˚C. FACTORY DEFAULT
ALTERNATOR #1 TOO HOT. 

OVER 108˚C
ALTERNATOR #2 TOO HOT. 

OVER 108˚C
VOLTAGE REGULATOR TOO 

HOT. OVER 90˚C
BATTERY SENSE WIRE OPEN 

OR NOT FOUND

BATTERY #1 TOO HOT.  OVER 

USER ADJUSTED VALUE
BATTERY #2 TOO HOT. OVER 

USER ADJUSTED VALUE
FIELD  VOLTAGE  TOO  HIGH                          

STATOR VOLTAGE TOO HIGH

SMALL ENGINE MODE IS IN 

OPERATION
BATTERY #2 TEMPERATURE 

SENSE MODE
ALTERNATOR #2 TEMPERATURE 

SENSE MODE

- 8 -

Summary of Contents for MAX CHARGE MC-612-DUAL

















Reviews: