Bally ProSlot 6000, Setup And Operation

Page: 37 / 444

©2004 Bally Gaming and Systems
2-37
ProSlot
®
6000
| - Revised, || - New
Diagnostic Tests and Functions
Item 01 7 d shows the two-digit code representing the
machine's denomination stored in SafeRAM™. Refer
to the DS2 DIP Switch table (page 2-10). The example
indicates a denomination of .25.
Item 01 8 d displays the Cyclic Redundancy Check,
CRC, of a JCM WBA bill acceptor ROM.
Item 01 9 d shows, when the Dallas Timekeeper IC is
installed at MPU U53, the date (mm dd: dw yy) and
time (hh mm: ss). The information takes four cycles
to complete and continues until exit. It can be paused
by holding
SPIN
.
#2 - Output Test
The Output Test begins a routine that selects and
turns on or off every output under microprocessor
control. There are 64 address locations numbered
in hexadecimal from 00 to 3F. The first digit of the
number represents the port and the second digit
represents the bit. For example, the number 28
represents port 2 bit 8.
The test is either auto-step or manual . Auto-step
advances through all ports while manual operation
allows the Operator to select the port and bit. Refer
to the Output table (page 2-37 - page 2-38).
Note: If game Option 80 is set to default
0000 (OFF), the electro-mechanical
meters will not be tested.
WIN PAID CREDIT COIN IN
0 1 9 d 0 4 1 1
25¢
WIN PAID CREDIT COIN IN
0 1 7 d 1 1
25¢
WIN PAID CREDIT COIN IN
0 1 8 d 4 2 1 1
25¢
#1 - Model Information (cont.)
Note:
Upon entering Output Test, the
first output tested is Port 2 Bit 0, Coin
Deflector Solenoid. Thereafter, the
ports cycle sequentially.
To select the Output Test, press and release the
TEST
button until the message 02 d appears in
WIN PAID
.
The test starts in auto-step operation as indicated by
020d in
WIN PAID
. The
CREDIT
display shows the two-digit
output number and port status (logic level). The status
toggles between 1 (logic high) and 0 (logic low).
The process repeats for all outputs. Pressing the
CHANGE
button while auto-cycling restarts the test.
To manually select an output, press the
PSEUDO
COIN
button on the front of the MPU assembly. W
IN
PAID
changes from
020d
to
021d
. Press the
CHANGE
button to select an output. Once selected, press the
TEST
button. W
IN PAID
shows
022d
. The port status in
CREDIT
toggles between
1
(logic high) and
0
(logic low)
reflecting the state of the output. Press the
TEST
button
again to constantly activate the output in either state.
The Message Center shows
021d
in
WIN PAID
. Exit by
pressing the
PSEUDO COIN
switch until
020d
displays in
WIN PAID
, indicating return to auto-step operation.
Exit the test by pressing
TEST
to advance to the next
diagnostic test; or by either pressing
RESET
or closing
the door to cause a system reset.
Port Bit Output Description
Output
Voltage
0 0 Top Tower Lamp 6.5 VAC
0 1 Bottom Tower Lamp 6.5 VAC
0 2 Bill Acceptor Ready 6.5 VAC
0 3 Bill Acceptor Not Ready 6.5 VAC
0 4 Coin Accepted Lamp 6.5 VAC
0 5 Insert Coin Lamp 6.5 VAC
0 6 Hold 3 Lamp 6.5 VAC
0 7 Hold 4 Lamp 6.5 VAC
0 8 Hold 5 Lamp 6.5 VAC
0 9 Hold 8 / Hold Attract Lamp 6.5 VAC
0 A Coin 7 / Hold 2 Lamp 6.5 VAC
0 B Coin 6 / Hold 1 Lamp 6.5 VAC
0 C Cash/Credit Lamp 6.5 VAC
0 D Bet One and Bet Max Lamps 6.5 VAC
0 E Spin Lamp 6.5 VAC
0 F Change Lamp 6.5 VAC
1 0 Coin 1 Lamp 6.5 VAC
1 1 Coin 2 Lamp 6.5 VAC
1 2 Coin 3 Lamp 6.5 VAC
1 3 Coin 4 Lamp 6.5 VAC
1 4 Coin 5 Lamp 6.5 VAC
1 5 Middle Tower Lamp 6.5 VAC
1 6 4th Tower Lamp 6.5 VAC
1 7 Jackpot Bell 6.5 VAC
1 8 Feature 1 Lamp 6.5 VAC
1 9 Feature 2 Lamp 6.5 VAC
1 A Feature 3 Lamp 6.5 VAC
1 B Feature 4 Lamp 6.5 VAC
1 C Feature 5 Lamp 6.5 VAC
1 D Feature 6 Lamp 6.5 VAC
1 E Feature 7 Lamp 6.5 VAC
1 F Feature 8 Lamp 6.5 VAC
2 0 Coin Deflector Solenoid +24 VDC
2 1 Total In Meter +24 VDC
2 2 Total Out Meter +24 VDC