Balluff Micropulse BTL5-A series User Manual Download Page 16 | Manualshive

Page: 16 / 16

Balluff Micropulse BTL5-A series User Manual Download Page 16

Sensors Worldwide

Inductive
Sensors

Connectors &
Accessories

Photoelectric
Sensors

Micropulse

TM

Transducers

Electromechanical
Sensors

Magnetic Field
Sensors

Identification
Systems

Capacitive
Sensors

Germany

Global Headquarters

Balluff GmbH
Schurwaldstraße 9
73765 Neuhausen a.d.F.
Telefon: +49 (0)71 58/1 73-0
Telefax: +49 (0)71 58/50 10
Hotline: +49 (0)71 58/1 73-370
Web: www.balluff.de
E-mail: [email protected]

USA

North American Headquarters

Balluff Inc.
8125 Holton Drive
Florence, KY 41042
Phone: (859) 727-2200
Toll-free: 1-800-543-8390
Fax: (859) 727-4823
Web: www.balluff.com
E-Mail: [email protected]

Canada

Balluff Canada, Inc.
2840 Argentia Road, Unit #2
Mississauga, Ontario L5N 8G4
Phone: (905) 816-1494
Toll-free: 1-800-927-9654
Fax: (905) 816-1411
Web: www.balluff.ca
E-mail: [email protected]

Mexico

Balluff de Mexico S.A. de C.V
Fray Pedro de Gante 25 P.B.
Col. Cimatario
Queretaro, QRO 76030
Phone: (++52 442) 212-4882,
224-3583, 224-3171
Fax: (++52 442) 214-0536
E-mail: [email protected]

Complete Product Range

Doc. n

o.

883597/Mat. no.

317093

E

•

Edition

03

12

; Subject to Modification

Z_Analog_122003.pmd

12/11/2003, 3:47 PM

14

«
...
14
15
16

Summary of Contents for Micropulse BTL5-A series

















Reviews:

No comments