1-800-543-8390
•
WWW.BALLUFF.COM
12
BTL5-A/C/E/G__-M____-B/Z-S32/KA__
Micropulse Linear Position Transducer
Analog Output-Rod Style
™
11.1 Dimensions, weights, ambient
conditions
•
Nominal length
< 4000 mm
•
Dimensions
Fig. 3-2
•
Weight
ca. 2 kg/m
•
Housing
anodized
aluminum
•
Pressure tube
stainless steel
1.4571
•
Diameter
10.2 mm
•
Wall thickness
2 mm
•
E-modulus
ca. 200 kN/mm
2
•
Mounting thread
M18×1.5 or
3/4"-16UNF
•
Operating temp.
–40 °C to +85 °C
•
Humidity
< 90 %, non-
condensing
•
Protection rating
per IEC 60529 IP 67
with connector attached
11.2 Supply voltage
(external)
Regulated supply voltage
BTL5-_1... DC 20 to 28 V
Ripple
< 0.5 V
pp
BTL5-_2... DC ±14.7 to ±15.3 V
Current draw
< 150 mA
Inrush
< 3 A/0.5 ms
Polarity reversal protection built-in
Overvoltage protection
Transzorb diodes
Electric strength
GND to housing
500 V
11 Technical Data
12 Versions (indicated on product label)
Supply voltage: 1 = DC 24 V, 2 = DC ±15 V
Electr. connection,
BTL5-A11-M0457-Z-S 32
KA05: with 5 cable
Rod Style,
Mounting: B = metric thread M18×1.5
includesnut
Z = thread 3/4"-16UNF
Nom. length (4digits): M = metric in mm
Voltage output A_1 = 10 ... 0 V and 0 ... 10 V
G_1 = 10 ... –10 V and –10 ... 10 V
Current output C_0 = 0 ... 20 mA
E_0 = 4 ... 20 mA
C_7 = 20 ... 0 mA
E_7 = 20 ... 4 mA
Micropulse
Linear T
ransducer
S 32: with connector,
Analog interface:
11.3 Outputs
B T L 5 - A . . .
Output voltage
0...10/10...0 V
Load current
< 5 mA
R i p p l e
< 5 mV
B T L 5 - G . . .
Output voltage
–10...10/10... –10 V
Load current
< 5 mA
R i p p l e
< 5 mV
B T L 5 - C . . .
Output current
0...20/20...0 mA
Load resistance
< 500 Ohm
B T L 5 - E . . .
Output current
4...20/20...4 mA
Load resistance < 500 Ohm
11.4 Connection to controller
Analog interface:
With S32 connector for shielded cable
(max length, see “Wiring”), diameter
6 to 8 mm, or with integral cable
(5m long)
11.5 Included in shipment
Transducer
Fig. 3-2
Calibration device
Fig. 6-1
11.6 Magnets
(order separately)
Magnets BTL-P-1013-4R,
BTL-P-1013-4S, BTL-P-1012-4R
Dimensions
Fig. 3-4
Weight
approx. 10 g
Housing
anodized
aluminum
Operating temp.
–40 °C to +85 °C
Magnets
BTL5-P-4500-1
(Electromagnet)
Weight
approx. 90 g
Housing
plastic
Operating temp.
–40 °C to +60 °C
11.7 Accessories
(optional)
Connectors
Fig. 4-3
Reso
Hysteresis
=
Repeatability
Voltage
0.3 mV
Current
0.6 µA
Minimum
0.05mm
Sampling rate f
Standard
= 2 kHz
Non-linearity
Nom. length
< 500 mm > 500 mm
in µm
±100
±0.02 % FS
Temperature coefficient
Voltage output:
[150 µV/K + (5 ppm/K
*
P
*
V/NL)]
*
∆
T
Current output:
[0,6 µA/K + (10 ppm/K
*
P
*
I/NL)]
*
∆
T
V
= output voltage range in [V]
I
= output current range in [mA]
NL
= nominal length in [mm]
∆
T
= temperature coefficient in [K]
P
= magnet position in [mm]
•
Shock
100 g/6 ms
per IEC 60068-2-27
1
•
Continuous shock
100 g/2 ms
per IEC 60068-2-29
1
•
Vibration
12 g, 10 to 2000 Hz
per IEC 60068-2-6
1
(take care to avoid inherent
resonances of protective tube)
•
Pressure
up to 600 bar
when installed in a hydraulic cylinder
1
Individual specifications as per
Balluff factory standard
Typical values at DC 24 V and 25 °C. Ready for operation at once, full accuracy after warm-up. With magnet:
BTL-P-1013-4R, BTL-P-1013-4S or BTL-P-1012-4R:
Z_Analog_122003.pmd
12/11/2003, 3:47 PM
12