WWW.BALLUFF.COM
•
1-800-543-8390
9
™
BTL5-A/C/E/G__-M____-B/Z-S32/KA__
Micropulse Linear Position Transducer
Analog Output-Rod Style
Enable buttons:
1. Press one of the buttons for at
least 3 s. Release button.
2. Within 1 s hold down buttons 1+2
simultaneously for at least 3 s. Now
the Error value remains stored as
the output signal.
Select adjust:
Hold down button 2 for at least 2 s
until the code for manual adjust is
displayed. Release button. The
current position value is displayed.
Adjust start value:
1. Move magnet to exact start
position.
2. Hold down button 1 for at least
2 s.
3. Shift null point (=start value)
towards flange or rod end with
constant slope: Briefly pressing
the buttons increases or
decreases the actual value by
approx. 1 mV or 2 µA. Holding a
button down for longer than 1 s
increases the step size.
4. Exit calibration procedure for the
start value: Press buttons 1+2
less than 2 s.
Adjust end value:
5. Move magnet to exact end
position.
6. Hold down button 2 for at least
2 s.
7. Increase or reduce slope: Briefly
pressing the buttons increases or
decreases the actual value by
approx. 1 mV or 2 µA. Holding a
button down for longer than 1 s
increases the step size.
8. Exit calibration procedure for the
end value: Press buttons 1+2 less
than 2 s.
Additional notes:
Setting the end value (i.e. the slope)
and the start value can mutually
affect each other depending on the
stroke position. You will need to
repeat steps 1 to 8 over until the
start and end values agree with their
respective desired values.
End adjustment, disable buttons:
Hold down buttons 1+2 simulta-
neously for at least 6 s to end the
calibration procedure until the Error
value is displayed. Then press one of
the buttons briefly (<1 s) to disable
both buttons.
Check your settings carefully
before starting up the system.
>2 s
>1 s
>1 s
1
1
–
+
++
– –
>1 s
>1 s
1
1
–
+
++
– –
10.50
3.60
2.00
6.00
V
V
5.39
V
9.15
1.34
4.82
1.00
1.00
4.40
4.40
V
V
V
V
4.00
>2 s
9.00
19.00
19.13
V
V
5.39
5.39
V
V
m
A
m
A
10.50
V
2.00
6.00
V
<2 s
10.00
20.00
V
>2 s
V
2.00
6.00
V
<2 s
9.00
19.00
>6 s
9.00
19.00
V
10.50
V
m
A
m
A
m
A
m
A
m
A
m
A
m
A
m
A
m
A
m
A
m
A
m
A
m
A
m
A
m
A
m
A
3.60
9.15
9.15
9.89
9.89
V
19.13
m
A
4.82
m
A
1.04
V
10.50
V
m
A
1
0.00
3.60
3.60
>3 s
<1 s
>3 s
1
/ 2
1
+ 2
1
+ 2
2
2
2
2
2
2
1
+ 2
1
+ 2
1
/ 2
<1 s
8 Manual adjust mode
adjust
End,
disable buttons
Current
position value
Code =
Error value
Code =
Error value
Code for
adjustment
Code for
adjusting start
value = Null value
New start
value
Code for
adjustment
Code for adjusting
end value = End
value
New end value
Code for
adjustment
Current
position
value
Current
position value
Current position
value
Current
position value
Current
position value
Current
position value
Current
position value
Code =
Error value
Code =
Error value
Current
position value
adjust
Enable buttons
BTL5-A... with magnet in stroke range
adjust
nd point
Z_Analog_122003.pmd
12/11/2003, 3:47 PM
9