background image

Manufactured under one or more of these patents. 

U.S. Patents: 5332944, 5361215, 5550753, 5559720, 5,883,459, 6253227, 6282370, 6590188, 6976052, 6965815, 7030343, 7,417,834 b2, Canadian Patent: 2342614, 

Australian patent: 2373248 other patents both foreign and domestic applied for and pending. All material copyright of Balboa Water Group.
42281_A | Compatible with SpaTouch 1 & 2

7

03.17

The Set Temperature

Press & Hold

The  Spa  Screen  shows  all  available  equipment*  to  control. 
The display shows icons that are related to the equipment
installed on a particular spa model, so this screen may change 
depending on the installation. The icon buttons are used to 
select and control individual devices.

Some devices, like pumps, may have more than one ON state, 
so the icon will change to reflect the state of the equipment. 
Below are some examples of 2-speed Pump indicators.

If the Spa has a Circ Pump, a Circ Pump Icon will appear to  
indicate  its  activity,  but  outside  of  Priming  Mode,  the  Circ 
Pump cannot be controlled directly.

*One exception: The Main Spa Light is not shown on the Spa 
Screen; it is only shown (and controlled) on the Main Screen.

Press Up or Down once to display the Set Temperature (indicated by a flashing 
ºF or ºC, plus a change in color of the temperature). Pess Up or Down again to 
modify the Set Temperature. The Set Temperature changes immediately.

If you need to switch between High Temperature Range and Low Temperature 
Range you need to go to the Settings Screen.

If Up or Down is pressed and held, the temperature will continue to change until 
you stop pressing, or until the Temperature Range limits are reached.

All Equipment Access

100 ºF

Jets Off

Jets Low

Jets High

Summary of Contents for SpaTouch2





























Reviews: