27
26
CHECKING THE CODES
If you have set up the Dolphin using the
“Searching For Your Code” procedure, you may
need to find out which four-digit code is operating
your equipment:
For example, to find out which code is operating
your TV:
1. Turn on your TV.
2. On the Dolphin, press and hold SETUP until the
LED blinks twice, then release SETUP.
3. Enter 9 - 9 - 0. The LED will blink twice.
4. To view the code for the first digit, press 1
once. Wait 3 seconds and count the number of
LED blinks (e.g., 3 blinks = 3) and write down
the number in the leftmost TV Code box below.
NOTE: If a code digit is “0”, the LED will not
blink.
5. Repeat step 4 three more times for remaining
digits. Use 2 for the second digit, 3 for the third
digit, and 4 for the fourth digit. Finish writing
down the code in the TV Code boxes below.
6. To check for the codes of your other
components, repeat steps 1 through 5, but
substitute the appropriate key (i.e., VCR,
CBL/SAT, DVD, CD or RCVR) for the component
you are checking. Write down the codes in the
appropriate boxes below.
TV Code
■
■ ■
■ ■
■ ■
■
VCR Code
■
■ ■
■ ■
■ ■
■
CBL/SAT Code
■
■ ■
■ ■
■ ■
■
DVD Code
■
■ ■
■ ■
■ ■
■
CD Code
■
■ ■
■ ■
■ ■
■
RCVR Code
■
■ ■
■ ■
■ ■
■
REASSIGNING DEVICE KEYS
The Dolphin can be set up to control a second TV
or VCR, or any combination of four home
entertainment components. For example, to have
the Dolphin control a TV, a Cable Converter, and
two VCRs, you will need to reassign the unused
RCVR key to operate the second VCR as follows:
1. On the Dolphin, press and hold SETUP until the
LED blinks twice, then release SETUP.
2. Enter 9 - 9 - 2. The LED will blink twice.
3. Press VCR once, then press RCVR once.
4. The RCVR key is now ready to be programmed
for your second VCR. See Programming VCR
Control on page 12.
To reassign other device keys, repeat steps 1
through 4 by substituting the key sequence from
the following chart for a desired component:
To Reassign
Perform Key Sequence
TV as 2nd VCR key:
SETUP - 9 - 9 - 2 - VCR - TV
TV as 2nd RCVR key:
SETUP - 9 - 9 - 2 - RCVR - TV
TV as 2nd CBL/SAT key:
SETUP - 9 - 9 - 2 - CBL/SAT - TV
TV back to TV
SETUP - 9 - 9 - 2 - TV - TV
VCR as 2nd TV key:
SETUP - 9 - 9 - 2 - TV - VCR
VCR as 2nd RCVR key:
SETUP - 9 - 9 - 2 - RCVR - VCR
VCR as 2nd CBL/SAT key: SETUP - 9 - 9 - 2 - CBL/SAT - VCR
VCR back to VCR:
SETUP - 9 - 9 - 2 - VCR - VCR
RCVR as 2nd TV key:
SETUP - 9 - 9 - 2 - TV - RCVR
RCVR as 2nd VCR key:
SETUP - 9 - 9 - 2 - VCR - RCVR
RCVR as 2nd CBL/SAT key: SETUP - 9 - 9 - 2 - CBL/SAT - RCVR
RCVR back to RCVR:
SETUP - 9 - 9 - 2 - RCVR - RCVR
Upon completion of a reassignment, the LED will
blink twice to confirm your selection. At that time,
you will also need to program the Dolphin to
control the new component (as described earlier
in this document).
