Azbil AUR455 User Manual Download Page 41

Page: 41 / 68

Chapter 4. Explanation of Operation

Operation during interlock (interlock activation during RUN)

If the interlock contacts are OFF, lockout occurs and an alarm is issued.

“

” (interlock) and “

” are displayed alternately.

Power supply
Burner start contacts
Interlock
Flame signal

Ignition transformer
Pilot valve
Main valve
Flame monitor output
Alarm output

SHUT
FL
AL

Input

Load output

LED indication

Standby

Start

check

Ignition trial

Pilot only

Main trial

Run

Lockout

Flame failure

response

Sequence display

Prepurge

E0 P8

* ON in the case of a direct ignition model, OFF in the case of an interrupted pilot model.

This is because the AUR455 has one output with different operation depending on the type of model, while the AUR450
has two outputs for the pilot valve, one for the intermittent and one for the interrupted type.

Operation during interlock (interlock activation between standby and start signal)

Even if the interlock contacts turn OFF before the start contact input, lockout does

not occur.

If the start signal is input in this state, lockout occurs and an alarm is issued. “

”

(interlock) and “

” are displayed alternately.

Power supply
Burner start contacts
Interlock
Flame signal

Ignition transformer
Pilot valve
Main valve
Flame monitor output
Alarm output

SHUT
FL
AL

Input

Load output

LED indication

Standby

Lockout

Sequence display

Prepurge

E0 P 1

Summary of Contents for AUR455





































































Search results

Summary of Contents for AUR455

Reviews:

Related manuals for AUR455

Brands by name

Popular brands

Azbil AUR455, User Manual

Search results

Summary of Contents for AUR455

Reviews:

Related manuals for AUR455

Brands by name

Popular brands