Azbil AUR455 User Manual Download Page 57

Page: 57 / 68

Chapter 6. Maintenance and Inspection

Alarm

code

Sub-

code

Description

Status

Cancellation method

Internal error EEPROM write

Error while writing to the EEPROM

Reset

Internal error process data value Internal memory error

Reset

System error (1)

CPU communication error

Reset

Internal error (input-circuit)

Detection of part failure (voltage applied to
the input terminals by wrong wiring) or strong
inductive electrical noise to the signal wire

Reset

Internal error (input-circuit)

Internal clock error

Reset

Internal error
(EEPROM data value)

An error was found in CPU mutual check.
There are discrepancies in EEPROM data.

Reset

Internal error
(CPU mutual check)

An error was found in the CPU internal status
mutual check.

Reset

Internal error
(CPU mutual check)

An error was found in the CPU process status
mutual check.

Reset

Internal error
(CPU mutual check)

CPU process synchronization error

Reset

Internal error (Alarm timeout) Internal feedback signal error of alarm output relay Reset

Internal error
(CPU mutual check)

Internal memory data error

•

While settings were being written with the
Smart Loader Package (SLP-A55), the power
was turned OFF or the loader cable was
removed.

Write settings using the
Smart Loader Package
(SLP-A55), and then do a
reset.

Internal error (flame circuit)

Error in the circuit for diagnosing the flame
detection circuit

Reset

Internal error (flame circuit)

Error in the interactive diagnosis of the flame
detection circuit

Reset

Internal error (K1 circuit)

Internal fuse burn-out, or internal feedback
signal error

Reset

Internal error (K2 circuit)

Internal feedback signal error

Reset

Internal error (PV circuit)

Internal feedback signal error

Reset

Internal error (MV circuit)

Internal feedback signal error

Reset

Internal error (IG circuit)

Internal feedback signal error

Reset

Internal error
(Communication setting)

Internal memory error in host communication
setting

•

In turn-down test or communication setting

mode, the power was turned off during

configuration (when the 7-segment display

was blinking), and data was not saved

correctly to the EEPROM.

•

Data was not correctly saved to the EEPROM

with the Smart Loader Package (SLP-A55)

because the power was turned OFF or the

loader cable was removed while settings

were being written, etc.

•

Due to some other failure of the EEPROM,

data was not correctly saved.

Reset the error.

The reset operation
initializes the
communication settings.
Please rewrite them with
the correct values.

See

Turn-down

test and communication
setting modes (Page 20).

Note

•

If a sequence cannot be identified, the sequence code where lockout occurred

may be “

” (stopped).

•

If lockout occurs even if the alarm is reset several times, there is a problem with

the product.

Summary of Contents for AUR455





































































Search results

Summary of Contents for AUR455

Reviews:

Related manuals for AUR455

Brands by name

Popular brands

Azbil AUR455, User Manual

Search results

Summary of Contents for AUR455

Reviews:

Related manuals for AUR455

Brands by name

Popular brands