manualshive.com logo in svg

Axis 2400, Administration Manual, Page: 55 / 80

Share
Download
Axis 2400 Administration Manual Download Page 55

 

AXIS 2400/2401

 

User’s Manual

Appendix E -

 

CGI Parameters

 

53

 

CGI Parameters for Pan Tilt and Zoom Control

Use the following syntax for creating CGI parameters to control Pan Tilt devices:

Example

Move the camera connected to VIDEO 1 on 

videoserv 

45 degrees to the right:

This table lists the CGI parameters for Pan Tilt requests:

Notes:

•Parameters and values identified with an asterisk “*” are not available to all supported pan tilt 

devices. For the latest driver-specific information, check out the Axis Camera Developer’s Web 
at http://cctv.axis.com/ 

•The CGI parameters that adjust the camera position are only applicable when using one of the 

suppor ted Pan/Tilt devices. 

http://<servername>/cgi-bin/control?camera=<n>&<parameter>=<value>[&<parameter>=<value>...]

http://videoserv/cgi-bin/control?camera=1&pan=45

Parameter/Syntax

Description

Values

camera=<n>

Selects the source for pan tilt requests. This is 
mandatory and must be submitted (for the AXIS 
2401this is always set to 1).

1,2,3 or 4

move=<x>

Moves the Pan/Tilt device 5 degrees in the 
specified direction.

up/down/left/right/upleft/upright/
downleft/downright/*home/

*pan=<n>

Pans the Pan/Tilt device <n> degrees relative to 
the home position.

-180 ... 180

*tilt=<n>

Tilts the Pan/Tilt device <n> degrees relative to 
the home position.

-180 ... 180

*rpan=<n>

Pans the Pan/Tilt device <n> degrees relative to 
the current position.

-180 ... 180

*rtilt=<n>

Tilts the Pan/Tilt device <n> degrees relative to 
the current position.

-180 ... 180

*zoom=<n>

Adjusts the camera zoom to the specified angle.

1 ... 999
where 1is full zoom out

zoomrel=<x>

Adjusts zoom to specified values.

wide/tel/*widemax/*telemax/

*focus=<x>

Adjusts zoom within the specified scale.

1 ... 999

*focusrel

Adjusts zoom to upper and lower extremes.

far or near

presetposno

Assumes the camera position defined by the 
preset position number.

1 ... 20

presetposname=<name>

Assumes the camera position defined by the 
preset position name.

<name>

*speed=<n>

Sets the head speed of the pan tilt device 
connected to the selected camera/port.

1 ... 999

whoami

identifies the type of pan tilt driver connected to 
the selected camera/port.

check

Summary of Contents for 2400

















































































Reviews:

No comments