Axis 2400 Administration Manual Download Page 45 | Manualshive

Page: 45 / 80

Axis 2400 Administration Manual Download Page 45

AXIS 2400/2401

Administration Manual

Appendix B -

Updating the Software

43

Before you begin:

Follow the instructions below to upgrade your video servers using AXIS ThinWizard:

1. Click the

Manage Network

button in the AXIS ThinWizard main menu.

2. Select a network group from the drop-down list. You can only update the servers that are

included in the selected network group.

3. All AXIS servers included in the network group appear. Click the

Firmware

button to start the

Upgrade Wizard.

4. Follow the instructions that are presented to you to complete the installation.

For more information about AXIS ThinWizard, refer to the Axis Website at

http://www.axis.com/

Upgrading using FTP

Having obtained the upgrade software, install it into the AXIS 2400/2401 by following the
instructions below:
1. Reset the AXIS 2400/2401 by powering it off and then on again.

2. Start an FTP session and log in to the AXIS 2400/2401 as

root

, using the root password. By

default this is set to

pass

.

3. Set FTP to binary mode using the command

bin

.

4. Download the new camera server software to you AXIS 2400/2401 by using the command

put

2400_xxx.bin flash

, where xxx is the version number for the firmware.

This process takes 30 - 60 seconds. The LEDs will flash slowly during programming.

Note:

If you need to force a download, e.g. when rever ting to an older version of software, use the syn-
tax

put 2400_xxx.bin FLASH

,

where

xxx

is the version number for the firmware.

5. The AXIS 2400/2401 will report

“

Transfer complete, flash programming finished

OK

”

, once the programming is complete.

Caution!

You must assign the AXIS 2400/2401 with an IP address, as described in

Assigning an IP Address,

on page

13, before you can use this upgrading method.

In controlled environments, flash memory upgrades provide a very safe method for updating software.
However, flash products can become damaged if the updating operation if not performed correctly.

Your dealer reserves the right to charge for repairs made nece ssary due to incorrect upgrading by the
user.

«
...
43
44
45
46
47
...
»

Summary of Contents for 2400

















































































Reviews:

No comments