Axiom CNC Series Assembly Manual Download | Manualshive

Page: 16 / 29

background image

16

3- Now proceed to the back of the machine. The rear assembly should be positioned as

shown making sure the hinges are positioned in towards the machine for the side doors.

Take care of the barrel connections at the back of the machine. There are two black

brackets to hold the polycarbonate in place that can be secured to the side installed

previously. Take care not to overtighten the screw on the clear polycarbonate.

Figure 26 Rear Enclosure Assembly

Figure 27 Barrel Connections

Figure 28 Rear Assembly Complete

«
...
14
15
16
17
18
...
»

Summary of Contents for CNC Series






























Reviews:

No comments

Related manuals for CNC Series

Brand: ZOLL Pages: 5

Brand: Accu-Chek Pages: 3

Brand: iBin Pages: 2

Brand: FEAS Pages: 72

Brand: Quincy lab Pages: 4

Brand: Cambridge Audio Pages: 2

Brand: Quanser Pages: 12

Brand: Hammer Strength Pages: 18

Brand: MacDon Pages: 238

Brand: Goobay Pages: 6

Brand: Daekyung Pages: 15

Brand: Zafferano Pages: 28

Brand: Basler Pages: 33

Brand: Elma Pages: 35

Brand: Qtx Pages: 6

Brand: Measumax Pages: 2

Brand: Bowa Pages: 140

Brand: Toparc Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands