Avnet Zynq-7000 AP SoC Getting Started Manual Download Page 18

Page: 18 / 21

Version 1.2

Zynq

-7000 AP SoC / Analog Devices Intelligent Drives Kit II

6. Select the disk listing that matches the SD card device using the

select disk

DiskPart command. In this

example, the SD card device is enumerated as the

Disk 1

device. If the SD card is listed as a different disk on

your system, be sure to substitute the appropriate value here.

WARNING

: Selecting the incorrect disk at this point can corrupt critical data on your local machine,

be sure to check that the selected disk value is the intended device.

DISKPART> select disk 1

7. List the partitions on the currently selected SD card using the

list partition

DiskPart command.

DISKPART> list partition

Figure 15 - Listing the Partitions on the Selected SD Card

8. Remove the partitions from the currently selected SD card using the

clean

DiskPart command.

DISKPART> clean

9. Exit the DiskPart tool.

DISKPART> exit

10. Extract the image contents of the archive obtained from Step 1 above using an

compatible utility such as 7-

Zip.

11.

Launch a disk imaging utility such as Win32 Disk Imager.

12. Select the source image file, for example

2014_R2-2015_04_24.img,

and choose the target drive device. In this

example, the image is located in the

C:\work\

folder and the target SD card is assigned to the

G:\

drive.

Summary of Contents for Zynq-7000 AP SoC






















Search results

Summary of Contents for Zynq-7000 AP SoC

Reviews:

Related manuals for Zynq-7000 AP SoC

Brands by name

Popular brands

Avnet Zynq-7000 AP SoC, Getting Started Manual

Search results

Summary of Contents for Zynq-7000 AP SoC

Reviews:

Related manuals for Zynq-7000 AP SoC

Brands by name

Popular brands