Avnet Zynq-7000 AP SoC Getting Started Manual Download Page 10 | Manualshive

Page: 10 / 21

background image

Version 1.2

Zynq

®

-7000 AP SoC / Analog Devices Intelligent Drives Kit II

10

Hardware Setup

Follow these steps closely to connect and configure the hardware to run the design.

1.

IMPORTANT:

Set the ZedBoard FMC IO voltage jumper to 2.5V to avoid any damage to the AD-

FMCMOTCON1-EBZ.

Figure 3 - Setting ZedBoard FMC IO Voltage to 2.5V

2. Set the ZedBoard boot-mode jumpers to boot from the SD card:

Figure 4 - Setting boot-mode jumpers to boot from the SD card

«
...
8
9
10
11
12
...
»

Summary of Contents for Zynq-7000 AP SoC






















Reviews:

No comments

Related manuals for Zynq-7000 AP SoC

Brand: Barracuda Networks Pages: 2

Brand: Palm Pages: 4

Brand: Keithley Pages: 59

Brand: Lattice Semiconductor Pages: 15

Brand: Profile Pages: 6

Supero SAS-826A

Brand: Supero Pages: 16

Brand: swiftech Pages: 2

RDGD3160I3PH5EVB

Brand: NXP Semiconductors Pages: 21

Brand: Holtek Pages: 280

Brand: Lucent Technologies Pages: 7

Broadband 700 MHz

Brand: Alcatel-Lucent Pages: 8

Brand: Intellinet Pages: 32

Brand: Cabletron Systems Pages: 56

Brand: RadiSys Pages: 6

Brand: Linksys Pages: 37

Brand: ADLINK Technology Pages: 29

Brand: Lobaro Pages: 26

Brand: Korg Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands