Avnet Zynq-7000 AP SoC Getting Started Manual Download Page 17 | Manualshive

Page: 17 / 21

background image

Version 1.2

Zynq

®

-7000 AP SoC / Analog Devices Intelligent Drives Kit II

17

Figure 12 - Opening the Windows Command Prompt with Administrator Privileges

4. If multiple partitions exist on the SD card, each of the partitions should be removed using the

diskpart

utility.

This will enable the entire SD card block range to be utilized for writing the image. Launch the

diskpart

tool from

the Windows Command Prompt.

> diskpart

Figure 13 - Launching Microsoft DiskPart

5. Discover the disk number of the SD card device by using the

list disk

DiskPart command. In this example, the

SD card device is enumerated as the

Disk 1

device.

DISKPART> list disk

Figure 14 - Listing the Enumerated Disk Devices

«
...
15
16
17
18
19
...
»

Summary of Contents for Zynq-7000 AP SoC






















Reviews:

No comments

Related manuals for Zynq-7000 AP SoC

Brand: 3Com Pages: 20

System x3630 M4

Brand: IBM Pages: 7

Brand: ebm-papst Pages: 16

APS6-400 Series

Brand: Eaton Pages: 114

IntroSpect Analyzer 2 Series

Brand: Aruba Pages: 5

Brand: XNET Pages: 17

Brand: OpenVox Pages: 13

Brand: QTech Pages: 406

Brand: Accusys Pages: 34

Brand: Navitar Pages: 1

airPoint Nexus sB3210

Brand: SmartBridges Pages: 55

Brand: Vivotek Pages: 46

Brand: Mod Pages: 11

Brand: Abocom Pages: 70

Brand: Airaya Pages: 28

Brand: HighPoint Pages: 3

Brand: LAWO Pages: 68

4 Channel Fan Speed Control Module CLX-1FAN4

Brand: Crestron Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands