EN
32
D - BEGINNING OPERATION
To adjust this value, follow this procedure
• Press
PROG
for 3 seconds › L0 will flash once
and L1 will turn on.
• Press
PROG
,
for 3 seconds › L0 will flash twice.
• Press
“+”
once › L2 will switch on instead of L1.
• Press
SET
› the number of LEDs that turn on will
indicate the set value.
• Use the
“–”
and
“+”
buttons to change this value
(see table below)
• Press
SET
to confirm this value › all
the LEDs will turn on and off to confirm the
operation.
LED on
L0
L1
L2
L3
L4
L5
Recharge
78cm 63cm 47cm 31cm 23cm 16cm
3.2.3 - PHOTOCELL SELF-TEST (OPTIONAL)
The system will perform a self-test on the photocells
(connected to
“PHO”
) several times:
• To detect photocells when the power is switched
on.
• To detect photocells when the operating mode
setting is confirmed.
• Before the gate is set into motion if they are active
for the time of movement requested.
• The reception and transmission photocells have a
separate power supply.
This test is performed in 3 steps:
1.
Power up the transmission and reception
photocells, and check if the “
PHO
” input is
earthed (which happens if the receiving photocell
receives an infrared beam).
2. Cut off the power supply to the transmission
photocell, and check whether the “
PHO
” input is
no longer earthed (absence of the infrared beam).
3. Restore power to the transmission photocell, and
check whether the “
PHO
” input is earthed again.
The photocell self-test is activated by default (Value
1). Most photocells on the market have a separate
power supply. If you wish to connect photocells with
a shared power supply, the self-test will not detect
these photocells. You can then deactivate it (Value
0).
To activate or deactivate this function, follow
the procedure below
• Press
PROG
for 3 seconds › L0 will flash once
and L1 will turn on.
• Press
PROG
,
for 3 seconds › L0 will flash twice.
• Press
“+”
twice › L3 will switch on instead of L1.
• Press
SET
.
• If L1 is switched on, the function is activated ›
press
“–”
to deactivate it, then
SET
to confirm.
• If L1 is switched off, the function is deactivated ›
press
“+”
to activate it, then
SET
to confirm.
If 2 sets of photocells are connected in a series, this
function does not enable you to detect a potential
fault in one of the sets.
It is still necessary to perform a manual test of all the
safety parts at least once every 6 months.
3.2.4 - PRE-FLASHING TIME
The flashing light is an essential safety
component.
It starts when a command to set the
gate in motion is received by the electronic card.
The gate is set in motion around one second after a
command is received.
In certain use cases, it is better that the time
between receiving a motion command and the start
of the manoeuvre is longer. It is possible to increase
this time to 3 seconds.
To set the pre-flashing time, follow the
procedure below
•
Press “
PROG
” for 3 seconds. L0 will flash once
and L1 will switch on.
•
Press “
PROG
” for 3 seconds. L0 will flash twice.
•
Press “+” 3 times and L4 will switch on instead of
L1.
•
Press
SET
.
•
If L1 is switched off, the time is 1 second. Press
“+” to increase it to 3 seconds, then
SET
to
confirm.
•
If L1 is switched on, the time is 3 seconds. Press
“–” to reduce it to 1 second, then
SET
to confirm.
CONNECTED MOTOR DRIVE KIT
