manualshive.com logo in svg

Avidsen 114461, Manual, Page: 34 / 56

Share
Download
Avidsen 114461 Manual Download Page 34

EN

34

CONNECTED MOTOR DRIVE KIT

D - BEGINNING OPERATION

To complete your registration, set a password 
between 6 and 20 characters long with letters and 
numbers only. then press

 

Terminé (Finished)

.

4.2 - CONNECTING THE CONTACTOR

As soon as it is switched on, the contactor will be 

in pairing mode by default. Its indicator light starts 

flashing until the pairing procedure is completed.

To start the pairing, press AJOUTER (ADD). Make 

sure your phone is connected to your router’s 2.4 

GHz WiFi network. If you already have a device 

installed on the application (e.g. IP camera, smart 

plug, etc.) click on + in the top right corner of the 

application. Select the product you wish to pair and 

select Home Gate. 

Make sure the contactor is connected and its 

indicator light is flashing. Otherwise, press the reset 

button for 5s so that the blue indicator light starts 

flashing. Select your 2.4GHz WiFi network

 (note

: 

your smartphone must be connected to the WiFi 

network to which the plug will be connected), enter 

your 

network password

 and press 

suivant (next)

.

IMPORTANT: if a location authorisation request 
message appears, you need to accept it for 
your Android or iOS device to receive your WiFi.

Summary of Contents for 114461

























































Reviews:

No comments