manualshive.com logo in svg

Avaya Secure Router 2330, Hardware Installation

Share
Download
Avaya Secure Router 2330 Hardware Installation Download Page 93

 Important:

The internal Compact Flash that ships with the Secure Router 2330 contains the system

image.

Prerequisites

• Ensure you have a Phillips #1 screwdriver.
• Ensure the Secure Router 2330 is powered off.
• Ensure you have a replacement Compact Flash ready to install.

Procedure steps

1. Remove the Secure Router 2330 top cover. For information, see 

Removing the

Secure Router 2330 top cover

 on page 86.

2. Locate the internal Compact Flash module.

See the following figure for reference.

3. Firmly grasp the Compact Flash by its edges and pull straight up to remove it from

the slot.

4. Insert the replacement Compact Flash in the slot, pushing down firmly but gently to

fully seat it in the slot.

Installing or removing the internal PVIM module on the Secure Router 2330

Installation — Hardware Components

August 2013     93

Summary of Contents for Secure Router 2330































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands