Avaya Secure Router 2330 Hardware Installation Download Page 47

Page: 47 / 126

Secure Router 4134 Internal hardware components

There are four internal hardware components that you can service or upgrade:

• DDR SO-DIMM
• VPN/IPSec module
• Packetized Voice Module (PVM)
• Internal system compact flash

The following figure shows the internal hardware components that are field serviceable. For

information about locating and removing the service panel to access the internal hardware

components, refer to

Avaya Secure Router 4134 Installation — Chassis

(NN47263-300).

Figure 26: Interior of the Secure Router 4134

Table 32: Internal components of the Secure Router 4134

Item

Description

VPN/IPSec module

Internal Compact Flash (CF0)—contains the system image

DDR SO-DIMM

Secure Router 4134 Internal hardware components

Installation — Hardware Components

August 2013 47

Summary of Contents for Secure Router 2330































































































































Search results

Summary of Contents for Secure Router 2330

Reviews:

Brands by name

Popular brands

Avaya Secure Router 2330, Hardware Installation

Search results

Summary of Contents for Secure Router 2330

Reviews:

Brands by name

Popular brands