manualshive.com logo in svg

Avaya Secure Router 2330, Hardware Installation

Share
Download
Avaya Secure Router 2330 Hardware Installation Download Page 92

Procedure steps

1. Remove the Secure Router 2330 top cover. For information, see 

Removing the

Secure Router 2330 top cover

 on page 86.

2. Locate the internal DIMM module.

See the following figure for reference.

3. Release the latches that secure the DIMM in the slot.

There is a release latch at both ends of the DIMM slot.

4. Firmly grasp the DIMM by its edges and pull straight up to remove the DIMM from

the slot.

5. Insert the replacement DIMM in the slot, pushing down firmly but gently to fully seat

it in the slot.

The release latches close when the DIMM is properly installed.

Replacing the Secure Router 2330 internal Compact Flash

Use the instructions in this section if you must replace the internal Compact Flash on the

Secure Router 2330. This internal device is not hot swappable.

 Caution:

The internal Compact Flash module is not hot swappable. Do not open the Secure Router

2330 top cover while the unit is powered.

Installing Avaya Secure Router 2330/4134 hardware components

92     Installation — Hardware Components

August 2013

Comments? [email protected]

Summary of Contents for Secure Router 2330































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands