manualshive.com logo in svg

Avaya Secure Router 2330, Hardware Installation

Share
Download
Avaya Secure Router 2330 Hardware Installation Download Page 123

Overcurrent warning statement

 Warning:

The Secure Router 2330/4134 relies on the building installation for overcurrent protection.
Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10 A
international) is used on the phase conductors.

 Warning:

WARNUNG

Nur qualifiziertes Wartungspersonal darf die Installation vornehmen. Lesen und befolgen
Sie die Warnungshinweise und Anweisungen, die auf dem Produkt gekennzeichnet oder in
der Dokumentation enthalten sind.

 Warning:

AVISO

Apenas profissionais de atendimento técnico qualificados devem realizar a instalação. Leia
e siga todos os avisos e instruções destacados no produto ou que façam parte da
documentação.

 Warning:

AVERTISSEMENT

L'installation doit être effectuée exclusivement par un personnel qualifié. Lisez et conformez-
vous à tous les avis et instructions d'avertissement indiqués sur le produit ou dans la
documentation.

 Warning:

AVISO

Apenas profissionais de atendimento técnico qualificados devem realizar a instalação. Leia
e siga todos os avisos e instruções destacados no produto ou que façam parte da
documentação.

 Warning:

AVVISO

L'installazione deve essere eseguita esclusivamente da personale qualificato. Leggere e
seguire tutti gli avvisi e le istruzioni presenti sul prodotto o inclusi nella documentazione.

Overcurrent warning statement

Installation — Hardware Components

August 2013     123

Summary of Contents for Secure Router 2330































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands