manualshive.com logo in svg

Avaya one-X Deskphone Edition, Installation And Maintenance Manual, Page: 12 / 74

Share
Download
Avaya one-X Deskphone Edition Installation And Maintenance Manual Download Page 12

9600 Series SIP IP Telephone Installation

12 9600 Series SIP IP Telephones Release 2.0 Installation and Maintenance Guide

 

Series SIP IP Telephones, see the instructions boxed with the telephone. Wall or desk mount 
instructions are also available on the Avaya support Web site 

http://www.avaya.com/support

. 

Software

The 9600 Series IP Telephones ship from the factory set to the H.323 protocol. To run the 
telephones in a SIP environment, you must convert the telephone(s) to SIP settings. Further, a 
factory-shipped 9600 Series IP Telephone will not contain the most up-to-date software for 
registration and SIP operation. When the telephone is first plugged in, a software download 
from an HTTP server might be initiated. The software download gives the telephone upgraded 
H.323 functionality, however, you must still download the latest SIP software bundle for 
telephones to be converted to SIP, then convert applicable telephones to run SIP software, as 
described in 

Converting Software on 9600 Series IP Telephones

on page 14.

For subsequent downloads of software upgrades, SIP Enablement Services (SES) provides the 
capability for a remote reboot of the IP telephone. As a consequence of restarting, the 
telephone automatically downloads new software if it is available. 

Chapter 4: Maintaining 9600 

Series SIP IP Telephones

 covers downloading new software releases.

Pre-Installation Checklist

Before plugging in the 9600 Series IP Telephones, verify that all the following requirements are 
met. Failure to do so prevents the telephones from working properly and can have a negative 
impact on the network. Print copies of this checklist for each server and IP telephone. 

Verify These Network Requirements

1.

 

Ensure that the LAN uses Ethernet Category 5e cabling running the IPv4 version of 
Internet Protocol.

2.

 

Ensure that the following is installed and/or set up and operative:

●

Avaya Communication Manager (CM) Release 4.0 or greater. 

●

SIP Enablement Services 4.0 or greater. 9600 Series SIP IP Telephones with 
SIP Release 2.0 software running on SES 4.0 servers have only those features 
compatible with that server.

●

NTP Time Server.

!

Important:

Important:

The above must be configured properly to support SIP. The CM 
Outboard Proxy SIP (OPS) Station Form must be completed to 
enable SIP prior to plugging in the telephones. For information, see 

Supporting SIP Phones in Communication Manager 4.0 

(Document 

Number 555-245-206, Issue 7, April, 2007).

Summary of Contents for one-X Deskphone Edition











































































Reviews:

No comments