manualshive.com logo in svg

Avaya one-X Deskphone Edition, Installation And Maintenance Manual, Page: 11 / 74

Share
Download
Avaya one-X Deskphone Edition Installation And Maintenance Manual Download Page 11

Issue 2 December 2007

11

 

Chapter 2: 9600 Series SIP IP Telephone Installation

Introduction

The 9600 Series SIP IP Telephones use Internet Protocol (IP) technology with Ethernet 
interfaces. The IP telephones supplement the existing Avaya IP Solutions platform.

The 9600 Series SIP IP Telephones support DHCP and HTTP/HTTPS over IPv4/UDP which 
enhance the administration and servicing of the telephones. These telephones use DHCP to 
obtain dynamic IP Addresses and HTTP or HTTPS to download new software versions or 
customized settings for the telephones.

All 9600 Series SIP IP Telephones provide the ability to have one IP connection on the desktop 
for both a telephone set and a PC using an Ethernet switch. 

In compliance with Australian law, the following information is provided:

This equipment shall be installed and maintained by trained service personnel. All the input/
output ports are classified as Safety Extra Low Voltage (SELV, in the meaning of IEC 
60950). To maintain safety compliance when connecting the equipment electrically to other 
equipment, the interconnecting circuits shall be selected to provide continued conformance 
of clause 2.3 for SELV circuits (generally, double/reinforced insulation to 240Vac rms to any 
primary/mains circuitry and 120Vac rms to any telecommunications network circuitry). To 
ensure that these conditions are adhered to, interconnect the equipment only with the 
already approved/certified equipment.

IP Telephone Models

There are five telephone set models currently defined in the 9600 Series SIP IP Telephone 
family:

The telephones have an internal Ethernet switch that allows the telephone and a PC to share 
the same LAN connection, if appropriate. Thus, 9600 models do not need, or work with, the 30A 
switched hub interface. Telephone models appended with "G" have a gigabit Ethernet (GigE) 
interface, which speeds data transmission.

This document describes the installation of these telephones and post-installation maintenance 
issues. For details about using the features provided by the telephones, see the user 
documentation for each telephone. For information about desk or wall mounting any of the 9600 

●

9620

9630G

9640G

●

9630 9640

 

Summary of Contents for one-X Deskphone Edition











































































Reviews:

No comments