manualshive.com logo in svg

Autonics PMC-1HS Series, Instruction Manual

Share
Download
Autonics PMC-1HS Series Instruction Manual Download Page 79

9. Serial Communication Commands

78

© Copyright Reserved Autonics Co., Ltd.

ERD

It reads the error status of the main body�

Format
Command

 [Axis specification] [CR]

ERD

 

X     [CR]

Y

Put the axis specification "X" in 1-axis (PMC-1HS).

[Response]

ERD

     X     

        [CR]

Y 

 

Error code of the main body

Bit composition of the Error status

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

Error code (BIT15-08)=0 means the error free status.
BIT15  HOME ERROR
BIT14  PROGRAM ERROR

　

 (PROGRAM OVERRUN ERROR

　

STEP>=Include 64)

BIT13  EMG ERROR
BIT12  ALARM ERROR
BIT11  HARDWARE LIMIT - ERROR
BIT10  HARDWARE LIMIT + ERROR
BIT09  SOFTWARE LIMIT - ERROR
BIT08  SOFTWARE LIMIT + ERROR

Error code 1 to 255

No-error: 0

Step number 0 to 63

Always zero
Step number information
0: No-step information, 1: Step information

IHS

It edits 2Byte EEPROM data. Data should be transmitted after converted to hexademical 4-digit.

Format
Command

 [Axis specification] [CR]

IHS

       X     EEPROM address , Data (hexademical 4-digit)     [CR]  

                Y 
[Example] To set Speed Multiplier of X-axis=100

                 IHS

XE6,0064

[Example] To set Step 1 Enable of X-axis home search mode to Enable

                 IHS

XF1,0001

[Response] Same with the written data

                   [Example] To set Speed Multiplier of X-axis=100

                                    IHS

XE6,0064

Summary of Contents for PMC-1HS Series



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands