manualshive.com logo in svg

Autonics PMC-1HS Series, Instruction Manual

Share
Download
Autonics PMC-1HS Series Instruction Manual Download Page 22

3. Configuration of the Operating Mode and System Parameters

21

© Copyright Reserved Autonics Co., Ltd.

(2) 

Home Signal Level (nSTOP1)

With the step 2, this mode configures the active level of the home signal (nSTOP1).

Display

Selection

Factory default

Home Signal Level (nSTOP1)

Low (GEX connection)/High (Open)

Low

Home signal on each axis is pin #10 of connector CN4 and 5.

For the active level, in case of selecting Low, the detecting operation of the step 2 started�

If the signal is connected to the GEX, the drive stops evaluating that the signal is active.

In case of High, the drive goes slow and stops evaluating that the opened signal is active�

(3) 

Z Signal Level (nSTOP2)

With the step 3, this mode configures the active level of the Encoder Z-phase signal (nSTOP2).

Display

Selection

Factory default

Z Signal Level (nSTOP2)

Low (GEX connection)/High (Open)

Low

The encoder Z-phase signal (nSTOP2) of each axis is pin #9 of connector CN4 and 5.

For the active level, in case of selecting Low, the detecting operation of the step 3 starts�

If the signal is connected to the GEX, the drive stops evaluating that the signal is active. When high, the 

drive stops evaluating that the opened signal is active�

(4) 

Step 1 to Step 4 Enable

This mode configures the Enable/Disable for each step.

Display

Selection

Factory default

Step 1 Enable to Step 4 Enable

Disable / Enable

Disable

If Disable is selected, the step is disabled and move to the next step�

If Enable is selected, the search operation of each step is carried in the specified direction. 

(5) 

Step 1 to Step 4 Direction

This mode configures the direction of each mode.

Display

Selection

Factory default

Step 1 Direction to Step 4 Direction

+/-

Step 1, 2

：－

Step 3, 4

：＋

If + is configured, the drive pulse comes out to the + direction of the detection direction.
If - is configured, the drive pulse comes out tn the - direction of the detection direction.

(6) 

Position Clear

When the home search ends, this mode clears the position counter�

Display

Selection

Factory default

Position Clear

Disable / Enable

Enable

Summary of Contents for PMC-1HS Series



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands