Autonics PMC-1HS Series Instruction Manual Download Page 11

Page: 11 / 82

2. Program Installation and Delete

© Copyright Reserved Autonics Co., Ltd.

2.4

Connection of RS-232C

1st Connect the motion controller and a PC using RS-232C communication cable�
2nd Turn on the motion controller and the PC�
3rd Start the operation program by selecting the [Start] button�

Click the Start → Program → Autonics → Motion Controller → PMC → PMC.

4th For initial access, the communication error message is popped up�

Click the [OK] button�

5th Select your product type, PMC-2HS or PMC-1HS.

6th Start the operation program as off-line�

Select Option and mark the COM port, the RS-232C communication cable is connected.

7th Restart the operation program� It will normally start in on-line mode�

Check the [OK] button to display the communication error message�

Summary of Contents for PMC-1HS Series



















































































Search results

Summary of Contents for PMC-1HS Series

Reviews:

Brands by name

Popular brands

Autonics PMC-1HS Series, Instruction Manual

Search results

Summary of Contents for PMC-1HS Series

Reviews:

Brands by name

Popular brands