manualshive.com logo in svg

Autonics PMC-1HS Series, Instruction Manual

Share
Download
Autonics PMC-1HS Series Instruction Manual Download Page 45

5. Drive by PC

44

© Copyright Reserved Autonics Co., Ltd.

5.3 

Parameter/Mode Screen

The parameter/mode screen of the Sub screen is used to configure modes, parameters and home search 

mode. This screen has Mode, Parameter and Home Search Mode tab.

5.3.1 

Mode Tab

The Mode tab is used to configure operation modes. Each mode is selected in the list by clicking (▼).

In online status, if each value is added or changed, the value is automatically added to the main body�

The mode tab is as listed in the table below� 

For more information, refer to '3.1.1 Mode'. 

Display

Selection

Factory default

Limit Stop Mode

Instant/Slow

Instant

Limit Active Level

Low/High

Low

Servo Inposition Enable 

Disable/Enable

Disable

Servo Inposition Level

Low/High

Low

Servo Alarm Enable

Disable/Enable

Disable

Servo Alarm Level

Low/High

Low

End Pulse

Disable/Enable

Disable

Deceleration Value

Accel/Decel

Accel

Soft Ware Limit

Disable/Enable

Disable

Power On Home Search Start

Disable/Enable

Disable

Power On Program Start

Disable/Enable

Disable

Summary of Contents for PMC-1HS Series



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands