Automation Direct T1K-DEVNETS User Manual Download Page 1

Page: 1 / 64

Errata Sheet

Page 1 of 1

Product Family

Terminator I/O

Manual Number

T1K-DEVNETS-M

Revision and Date

1st Edition; November 2001

Date

December 2018

This Errata Sheet contains corrections or changes

made after the publication of this manual.

Errata Sheet

Changes to Chapter 2. Installing the T1K–DEVNETS Base Controller
Page 2-9. Configuring the Controller; Status Indicators

Replace the top portion of the table [MS (Module Status) Indicator] with the table below.
Two new rows were added for Flashing Green and Flashing Red.
No changes were made to the lower portion of the table [NS (Network Status) Indicator].

MS (Module Status) Indicator

Indication

Status

OFF

No power to Controller. Check wiring.

ON (Green)

Power applied to Controller, no fault

ON (Red)

Critical Controller Fault

Flashing Green

In Firmware Update Mode

Flashing Red

I/O system error

Missing module error

New module present error

I/O diagnostic error

Summary of Contents for T1K-DEVNETS

































































Search results

Summary of Contents for T1K-DEVNETS

Reviews:

Related manuals for T1K-DEVNETS

Brands by name

Popular brands

Automation Direct T1K-DEVNETS, User Manual

Search results

Summary of Contents for T1K-DEVNETS

Reviews:

Related manuals for T1K-DEVNETS

Brands by name

Popular brands