AudioCodes MP-104 Quick Start Installation Manual Download Page 18

Page: 18 / 19

Page 18 of 19

AudioCodes™ MP-104 Gateway Quick Start Installation Guide

August 2004

Software Update:

Allows you to update configuration files using TFTP or HyperText

Transfer Protocol (HTTP).

•

Software Upgrade Wizard:

Allows you to download the configuration files. This

Wizard is helpful when upgrading to version newer than v4.4. To download the
files, click

Start Software Upgrade

and follow the instructions on the Wizard.

•

Load Auxiliary Files:

Allows you to upload the INI, Coefficient, and Call

Progress Tone files. To upload the files, click

Browse

to select the appropriate

file(s), then click

Send File

NOTE:

Currently the Voice Prompt and Pre Recorded Tones files are not used on

Axxess systems.

Save Configuration:

Click

Save Configuration

to save configuration to the system.

10.

Reset:

Check

Burn

and click

Reset

to restart the system.

Summary of Contents for MP-104




















Search results

Summary of Contents for MP-104

Reviews:

Related manuals for MP-104

Brands by name

Popular brands

AudioCodes MP-104, Quick Start Installation Manual

Search results

Summary of Contents for MP-104

Reviews:

Related manuals for MP-104

Brands by name

Popular brands