ATEN VM5404HA User Manual Download Page 94

Page: 94 / 122

VM5404HA / VM5808HA User Manual

Configure other IP settings as needed. Default settings are indicated in
bold.



IP Address –

192.168.0.60



Subnet Mask –

255.255.255.0



Default Gateway –

192.168.0.1



Website Timeout* – N/A,

, 10, 30, 60 minutes



Telnet Configuration –

enabled

Note:



The Website Timeout setting controls how long an inactive web
connection stays logged into the VM5404HA / VM5808HA. Any
changes will take effect immediately. The default setting is 5 minutes.



To reset the system network settings, go to

Settings

Maintenance

System Setup

, and then click the

reset to default

button.

3. Enter the values, then click Save. Changes may take a few seconds and

after refreshing the page automatically redirects you to the IP address
specified.

Summary of Contents for VM5404HA



























































































































Search results

Summary of Contents for VM5404HA

Reviews:

Related manuals for VM5404HA

Brands by name

Popular brands

ATEN VM5404HA, User Manual

Search results

Summary of Contents for VM5404HA

Reviews:

Related manuals for VM5404HA

Brands by name

Popular brands