ATEN VM5404HA User Manual Download Page 89

Page: 89 / 122

Chapter 4. Browser Operation

Maintenance

System Setup

You can use the System Setup page to do any of the following:



Upgrade the firmware of the VM5404HA / VM5808HA.



Back up and restore the VM5404HA / VM5808HA’s system settings. Note
that account settings cannot be backed up or restored.

Firmware Upgrades

1. Download the firmware package from ATEN’s official website.

2. In the VM5404HA / VM5808HA web interface, go to

Settings

Maintenance

System Setup

Firmware Upgrade

Mainboard I/O

Board

, and click

Browse

to locate the firmware upgrade package.

3. Click

Upgrade

to begin the upgrade.

Note:

After updating the firmware, it’s recommended that you clear your web
browser’s cache and then reopen the web browser. This will ensure that
the web console refreshes and functions properly.

Summary of Contents for VM5404HA



























































































































Search results

Summary of Contents for VM5404HA

Reviews:

Related manuals for VM5404HA

Brands by name

Popular brands

ATEN VM5404HA, User Manual

Search results

Summary of Contents for VM5404HA

Reviews:

Related manuals for VM5404HA

Brands by name

Popular brands