ATEN VM5404HA User Manual Download Page 105

Page: 105 / 122

Chapter 5. CLI Commands

Fan Speed Command

The Fan Speed command allows you to set the internal fan speed that cools the
VM5404HA/VM5808HA.

To set the fan speed, use the following command:

C C [Enter]

1. For example, to set the fan to low speed, type:

fan low [Enter]

The following tables show the possible values for the

Fan Speed

command:

Note:

Each command string can be separated with a space.

The following table lists the available Fan Speed commands:

Command

Description

fan

Fan Speed Command

Control

Description

low

Set internal fan to low speed (default)

mid

Set internal fan to normal speed

high

Set internal fan to high speed

Command

Control

Enter

Description

fan

low

[Enter]

Sets fan speed to low

fan

mid

[Enter]

Sets fan speed to normal

fan

high

[Enter]

Sets fan speed to high

Summary of Contents for VM5404HA



























































































































Search results

Summary of Contents for VM5404HA

Reviews:

Related manuals for VM5404HA

Brands by name

Popular brands

ATEN VM5404HA, User Manual

Search results

Summary of Contents for VM5404HA

Reviews:

Related manuals for VM5404HA

Brands by name

Popular brands