ATEN VM5404HA User Manual Download Page 63

Page: 63 / 122

Chapter 4. Browser Operation

Port Settings



Configure the OSD and CEC port

settings.



Configure the HDCP key for input and

output ports.



Configure the Seamless Switch™

settings.



Name the input and output ports.



Select EDID modes.



Configure the local output settings.

For more information,
see

Port Settings

page 53.

Status



View statuses of the input/output boards

installed to the VM5404HA / VM5808HA
and enable/disable FrameSync and
Long Reach mode for the board.



View system information such as

network settings, firmware version, and
the settings for audio/video assignment,
volume, CEC, audio mode settings, and
more.

For more information,
see

YCBCR 4:2:0 Video

Data Block

, page 70.

Maintenance



Upgrade the firmware for the installed

input and output boards



Back up or restore the VM5404HA /

VM5808HA’s configuration



Add, edit, or remove user accounts



Configure the system network settings

See

Maintenance

page 77.

Option

Description

Click

Save

to apply the settings.

Click

Cancel

to discard changes and reset settings.

Tab

Supported Functions

Detailed Information

Summary of Contents for VM5404HA



























































































































Search results

Summary of Contents for VM5404HA

Reviews:

Related manuals for VM5404HA

Brands by name

Popular brands

ATEN VM5404HA, User Manual

Search results

Summary of Contents for VM5404HA

Reviews:

Related manuals for VM5404HA

Brands by name

Popular brands