manualshive.com logo in svg

ATEN VM51616H, User Manual

Share
Download
ATEN VM51616H User Manual Download Page 97

Chapter 5. RS-232 Commands

87

Switch Port Command

The Switch Port command allows you to switch ports on the VM51616H.

The formula for the Switch command is as follows:

C Input + Group + Control 
+ [Enter] 

1. For example, to switch input port 02 to output port 05, type:

sw i02 o05 [Enter]

2. To switch output port 04 to the next port, type:

sw o04 [Enter] 

3. To turn off video output on port 03, type:

sw o03 off [Enter]

4. To switch audio from input port 06 to stereo audio output, type:

sw i06 console audio [Enter]

The following tables show the possible values for the 

Switch Port 

command:

 

  

Command

Description

sw

Switch command

Input Command

Description

i

Input command

Port number

Description

xx

01-16 port 

Output Command

Description

o

Output command

Port number

Description

yy

01-16 port

*

All output ports

Group

Description

normal

default HDMI audio outputs

console audio

Switch the audio to the stereo audio 
output

Summary of Contents for VM51616H





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands