Asus RS500-E8-PS4 User Manual Download Page 24

Page: 24 / 194

Chapter 2: Hardware setup

2-2

2.1

Chassis cover

Removing the rear cover

Locate and remove the front side screws.

Firmly hold the cover and slide it toward

the rear panel for about half an inch

until it is disengaged from the chassis.

Lift the cover from the chassis.

To recover the rear cover, reverse step

1 to 4.

Loosen the two thumbscrews on the rear panel to release the rear cover from the

chassis.

Thumbscrews

A protection film is pre-attached to

the system cover before shipping.

Please remove the protection film

before turning on the system for

proper heat dissipation.

Front side screw

Summary of Contents for RS500-E8-PS4



































































































































































































Search results

Summary of Contents for RS500-E8-PS4

Reviews:

Related manuals for RS500-E8-PS4

Brands by name

Popular brands

Asus RS500-E8-PS4, User Manual

Search results

Summary of Contents for RS500-E8-PS4

Reviews:

Related manuals for RS500-E8-PS4

Brands by name

Popular brands