Asus RS500-E8-PS4 User Manual Download Page 40

Page: 40 / 194

Chapter 2: Hardware setup

2-18

2.5.4

Configuring an expansion card

After installing the expansion card, configure the it by adjusting the software settings.

Turn on the system and change the necessary BIOS settings, if any. See Chapter 5 for

information on BIOS setup.

Assign an IRQ to the card. Refer to the following tables.

Install the software drivers for the expansion card.

Standard Interrupt assignments

* These IRQs are usually available for ISA or PCI devices.

IRQ

Priority Standard function

System Timer

Keyboard Controller

Programmable Interrupt

Communications Port (COM2)

Communications Port (COM1)

Floppy Disk Controller

System CMOS/Real Time Clock

ACPI Mode when used

10*

IRQ Holder for PCI Steering

11*

IRQ Holder for PCI Steering

12*

PS/2 Compatible Mouse Port

Numeric Data Processor

14*

Primary IDE Channel

15*

Secondary IDE Channel

Summary of Contents for RS500-E8-PS4



































































































































































































Search results

Summary of Contents for RS500-E8-PS4

Reviews:

Related manuals for RS500-E8-PS4

Brands by name

Popular brands

Asus RS500-E8-PS4, User Manual

Search results

Summary of Contents for RS500-E8-PS4

Reviews:

Related manuals for RS500-E8-PS4

Brands by name

Popular brands