Asus RS500-E8-PS4 User Manual Download Page 56

Page: 56 / 194

Chapter 4: Motherboard information

4-8

4.3

Internal connectors

Serial ATA 6.0 / 3.0 Gbps connector (7-pin SATA6 [Light Blue])

Supported by the Intel

610 series Chipset, this connector is for the Serial ATA signal

cables for Serial ATA hard disk drives that allows up to 6 Gbps of data transfer rate.

The actual data transfer rate depends on the speed of Serial ATA hard disks installed.

Power Supply SMBus connector (5-pin PSUSMB1)

This connector allows you to connect SMBus (System Management Bus) to the PSU

(power supply unit) to read PSU information. Devices communicate with an SMBus

host and/or other SMBus devices using the SMBus interface.

This connector functions only when you install the ASUS ASMB8.

Summary of Contents for RS500-E8-PS4



































































































































































































Search results

Summary of Contents for RS500-E8-PS4

Reviews:

Related manuals for RS500-E8-PS4

Brands by name

Popular brands

Asus RS500-E8-PS4, User Manual

Search results

Summary of Contents for RS500-E8-PS4

Reviews:

Related manuals for RS500-E8-PS4

Brands by name

Popular brands