Asus RS500-E8-PS4 User Manual Download Page 32

Page: 32 / 194

Chapter 2: Hardware setup

2-10

2.3

System memory

2.3.1 Overview

The motherboard comes with sixteen (16) Double Data Rate 4 (DDR4) Dual Inline Memory

Modules (DIMM) sockets.
The figure illustrates the location of the DDR4 DIMM sockets:

2.3.2

Memory Configurations

You may install 4 GB, 8 GB, 16 GB, and 32 GB RDIMMs or 32 GB, 64 GB LR-DIMMs and

NVDIMM into the DIMM sockets using the memory configurations in this section.

•

Always install DIMMs with the same CAS latency. For optimum compatibility, it is

recommended that you obtain memory modules from the same vendor.

•

Start installing the DIMMs in slots A1 or B1.

Summary of Contents for RS500-E8-PS4



































































































































































































Search results

Summary of Contents for RS500-E8-PS4

Reviews:

Related manuals for RS500-E8-PS4

Brands by name

Popular brands

Asus RS500-E8-PS4, User Manual

Search results

Summary of Contents for RS500-E8-PS4

Reviews:

Related manuals for RS500-E8-PS4

Brands by name

Popular brands