background image

Copyright © 2019-2020, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole 

or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9360-1030-020  Rev 6  11/20

5

D6021/D6031 Double Unit Series

 (Push Side) Power Operator

Prepare Frame and Door 

Figure 1 

Become familiar with operator components and fasteners.

 

It is recommended that components remain in boxes 

until installed. Verify there is minimum ceiling clearance for operator installation before proceeding. (Figure 1)

A.   Prepare frame.

1.  Determine if push or pull installation. (Figure 2) 

 

NOTE: These instructions are for Pair of Doors, 

PUSH only. See 80-9360-1029-020 instructions 

for D6011/D6051 or 80-9360-1031-020 

instructions for D6061/D6071 Push installation.

 

2. 

Frame header MUST be flat / without twists. 

Backplates can be used as reference.  

 

NOTE: If frame is not flat or is twisted, 

additional steel back plates or shimming is 

required. Failure to mount units properly can 

result in improper function of operator or 

inability to snap on covers. 

 

3.  Mark center of opening on frame header 

between jambs.

 

4.  Using chart, mark from center of opening to 

left

(Figure 3) 

 

NOTE: Template provided on page 28.

 

5. 

Measure 5/16" up from bottom of frame header 

and mark at Dim A and Dim B locations.

 

 

6.  Drill holes. 

7.  Using supplied backplate screw pack in Box 1, 

insert screws into prepared mounting holes. 

 

For Metal Frame:

 Use two (2) 1/4-20 x 1" flat 

head machine screws. 

 

For Wood Frame:

 Use two (2) #14 x 1-1/2" flat 

head self-drilling screws. 

 

NOTE: Do not tighten mounting screws at 

this time. Leave 5/16" minimum (thickness of 

backplate) between frame face and back of 

screw head.

OR

Figure 2 

Figure 3 

Center of Opening

Pull Side

Push Side

Right Hand

PUSH

Left Hand

PUSH

Door Size

Dim A

Dim B

Pair of 36" doors: 5-9/16" (141mm)

30-9/16" (776mm)

Pair of 38" doors: 7-9/16" (192mm)

32-9/16" (827mm)

Pair of 40" doors: 9-9/16" (243mm)

34-9/16" (878mm)

Pair of 42" doors: 11-9/16" (294mm) 36-9/16" (929mm)
Pair of 44" doors: 13-9/16" (344mm) 38-9/16" (979mm)
Pair of 46" doors: 15-9/16" (395mm) 40-9/16" (1030mm)
Pair of 48" doors: 17-9/16" (446mm) 42-9/16" (1081mm)

Summary of Contents for Norton D6001BP-38-LH





























Reviews: