background image

Copyright © 2019-2020, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole 

or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9360-1030-020  Rev 6  11/20

D6021/D6031 Double Unit Series

 

(Push Side) Power Operator

Installation Instructions

Tools Needed

1/4-20

#7

#2 and #3

10" or 12"

3/8

Punch

Set (Inch)

Supplied Fasteners per Operator

D6031 Push Side (Handed)  

110° to 180° opening

All components above with 6030-1W main arm and rod 
instead of 6020-1W

D6021 Push Side  

up to 110° opening

Union Assembly

(D6001U)

Union Spacer

(6001US)

End Cap - RH

(6001ENRH)

Closer Assembly

(7500LAP)

Operator LAP

(6021LAP)

Conduit Assembly

(D6001CON)

Power Module Sub-assembly

(6001PM)

Power Supply

(6000SUP)

Inverter

(6000IN)

End Cap - LH

(6001ENLH)

Union Spacer

(6001US)

Operator LAP

(6021LAP)

Inverter

(6000IN)

Power Supply

(6000SUP)

Power Module Sub-assembly

(6001PM)

Closer Assembly

(7500LAP)

Main Arm and Rod

(6030-1W)

Adjusting Tube and 

Shoe

(6620-12) x2

Main Arm and Rod

(6020-1W) x2

Pour la version francaise voir www.nortondoorcontrols.com. 
READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

This product can expose you to lead which is known to the state of 

California to cause cancer and birth defects or other reproductive harm. 

For more information go to www.P65warnings.ca.gov.

WARNING

(D6001COV-36

D6001COV-38

D6001COV-40

D6001COV-42

D6001COV-44

D6001COV-46

D6001COV-48)

Backplate - LH

(D6001BP-36-RH

D6001BP-38-RH

D6001BP-40-RH

D6001BP-42-RH

D6001BP-44-RH

D6001BP-46-RH

D6001BP-48-RH)

Backplate - RH

Cover

(D6001BP-36-LH

D6001BP-38-LH

D6001BP-40-LH

D6001BP-42-LH

D6001BP-44-LH

D6001BP-46-LH

D6001BP-48-LH)

(D6001COV-36

D6001COV-38

D6001COV-40

D6001COV-42

D6001COV-44

D6001COV-46

D6001COV-48)

Summary of Contents for Norton D6001BP-38-LH





























Reviews: