ASEA AC100Q-3 Operation Manual Download Page 5

Page: 5 / 67

AC100Q-3 Operations Manual....

SOFTWARE FEATURES .................................................................................................39
7.1

GENERAL .............................................................................................................39

7.2

LOAD MANAGEMENT.......................................................................................39

7.3

LOAD MANAGEMENT OPERATION ...............................................................41
7.3.1 Shore Cord Alarm, Single, Master, and Slave converters .........................41

7.3.2  Shore Cord Setup, Single, Master, or Slave Converters ............................42
7.3.3  Voltage Droop, Single or Master Converters ............................................43
7.3.4  Automatic Transfer to Generator, Single or Master Converters (Seamless

Transfer installed) ......................................................................................44

7.3.5 Quick Setup of Shore Cord Alarm, Single, Master, or Slave Converters ..45

7.4

GENERATOR FREQUENCY ANALYSIS .........................................................46

7.5

CONVERTER OUTPUT IMPEDANCE CONTROL...........................................46

7.6

AGC CONTROL ...................................................................................................47

7.7

kW-HOUR METER AND MAXIMUM POWER LEVEL DISPLAY .................48

7.8

CONVERTER OUTPUT VOLTAGE CONTROL ...............................................49

7.9

EVENT LOG .........................................................................................................50

TROUBLE-SHOOTING AND DIAGNOSTICS ..............................................................52

8.1

COMMON PROBLEMS .......................................................................................52

8.2

FAILURE AND WARNING MESSAGES ...........................................................53

8.3

INFO DISPLAY ....................................................................................................53

8.4

STATUS WORDS .................................................................................................54

8.5

GATHERING DATA ............................................................................................54

8.6

SOFTWARE TOOLS ............................................................................................54

8.7

POWER MODULE SWITCH ...............................................................................56

8.8

POWER MODULE FUSES ..................................................................................56

CALIBRATION ................................................................................................................57

MAINTENANCE ..............................................................................................................59

INTERNATIONAL POWER FORM REFERENCE ........................................................60

INDEX ...............................................................................................................................67

FIGURES

SYSTEM BLOCK DIAGRAM ...........................................................................................8

MECHANICAL OUTLINE...............................................................................................15

CONTROLS ......................................................................................................................16

INPUT AND OUTPUT CONNECTIONS ........................................................................19

FRONT PANEL CONTROLS ..........................................................................................24

RS-232C PINOUT .............................................................................................................35

RS-485 CONNECTIONS ..................................................................................................36

STATUS WORD BIT DEFINITIONS ..............................................................................55

POWER MODULE SWITCH AND LED .........................................................................56

POWER MODULE FUSES ..............................................................................................56

Summary of Contents for AC100Q-3




































































Search results

Summary of Contents for AC100Q-3

Reviews:

Related manuals for AC100Q-3

Brands by name

Popular brands

ASEA AC100Q-3, Operation Manual

Search results

Summary of Contents for AC100Q-3

Reviews:

Related manuals for AC100Q-3

Brands by name

Popular brands