manualshive.com logo in svg

ASEA AC100Q-3, Operation Manual

Share
Download
ASEA AC100Q-3 Operation Manual Download Page 2

 

AC100Q-3 Operations Manual....

2 

 

 

CERTIFICATION

 

 
 

ASEA Power Systems certifies that this product was thoroughly tested and inspected and found to meet or 

exceed its published specifications when shipped from the factory.

 

 

WARRANTY

 

 

ASEA  Power  Systems  warrants  each  unit  to  be  free  from  defects  in  material  and  workmanship.    For  a 

period of 18 months after purchase or 12 months after installation (whichever is shorter), ASEA Power 

Systems will repair or replace any defective module provided the unit has been installed and operated in a 

manner according to this manual.    A thorough inventory of spare parts & modules is maintained at our 

factory.    Our world-wide sales/support facilities also inventory a complement of spare parts and modules. 

 

ASEA Power Systems is not responsible for consequential damage arising from the use of its equipment.   

It does not apply to extensively modified or non-standard systems.    Debit memos for returned

 units are 

not accepted, and will cause return of the system without repair. 

 

 

LIFE SUPPORT POLICY

 

 

ASEA Power Systems does not authorize the use of any of its products or systems for use an AC voltage 

supply (source) for life support systems.    Life support systems are devices which support or sustain life, 

and  whose  failure  to  perform,  when  properly  used  in  accordance  with  this  Operations  Manual,  can  be 

reasonably expected to result in significant injury to the user.

 

Summary of Contents for AC100Q-3




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands