ASEA AC100Q-3 Operation Manual Download Page 45

Page: 45 / 67

AC100Q-3 Operations Manual....

7.3

LOAD MANAGEMENT OPERATION, cont.

7.3.5 Quick Setup of Shore Cord Alarm

, Single, Master, or Slave Converters

1. Turn on the red Disconnect switch of both converters and wait 15-20 seconds for initialization.

2. Press the

SHORE POWER

buttons on both converters.

3. Press the Cursor (

) button to advance to the ALARM AT % setting.

4. Set the converter ALARM AT % using the More/Less (

) buttons.

5. Press the Cursor (

) button to advance to the ALARM enable setting.

6. Set the converter ALARM enable using the Enable/Disable (

) buttons.

7. Press the Exit (

) button to save the settings and exit.

8. Turn on the converters and place online as usual. Alarm will occur when loading reaches the

ALARM AT % setting.

Quick Setup of Load Sharing

, paralleled Converters

1. Turn on the red Disconnect switch of both converters and wait 15-20 seconds for initialization.

2. Press the

SHORE POWER

buttons on both converters.

3. Press CORD (

) on both converters.

4. Set the Master’s SHORE CORD AMPACITY in amps using the More/Less (

) buttons.

5. Set the Slave’s MASTER CAPACITY in kVA (read from the Master’s Shore Cord Setup

screen) using the More/Less (

) buttons.

6. Advance to the Slave’s SLAVE CORD AMPACITY using the Forward (

) button and set the

amps using the More/Less (

) buttons.

7. Press the Exit (

) button twice on both converters to save the settings and exit.

8. Turn on the converters and place online as usual, and verify an imbalanced share in Load Level

% or individual Converter Output Amps at a ratio approximate to that ratio between the

converter’s programmed capacities.

Summary of Contents for AC100Q-3




































































Search results

Summary of Contents for AC100Q-3

Reviews:

Brands by name

Popular brands

ASEA AC100Q-3, Operation Manual

Search results

Summary of Contents for AC100Q-3

Reviews:

Brands by name

Popular brands