background image

MAT-8000

3

1. Safety precautions.

•  Be sure to read the instructions in this section carefully before use.

•  Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded 

as very important precautions are included.

•  We also recommend you keep this instruction manual handy for future reference.

Warnings and safety.

Safety Symbol and Message Conventions.
Safety symbols and messages described below are used in this manual to prevent bodily injury and property damage, 

which could result from mishandling. Before operating your product, read this manual first and understand the safety 

symbols and messages so you are thoroughly aware of the potential safety risk.

Warning.

When Installing the Unit.
•  Do not expose the unit to rain or an environment 

where it may be splashed by water or other liquids, as 

doing so may result in fire or electric shock.

•  Use the unit only with the voltage specified on 

the unit. Using a voltage higher than that which is 

 specified may result in fire or electric shock.

•  Do not cut, kink, otherwise damage nor modify the 

power supply cord. In addition, avoid using the power 

cord in close proximity to heaters, and never place 

heavy objects -- including the unit itself -- on the 

power cord, as doing so may result in fire or electric 

shock.

•  Be sure to replace the unit’s terminal cover after 

 connection completion. Because high voltage is applied 

to the speaker terminals, never touch these terminals 

to avoid electric shock.

•  Be sure to ground to the safety ground (earth) 

 terminal to avoid electric shock. Never ground to  

a gas pipe as a catastrophic disaster may result.

•  Avoid installing or mounting the unit in unstable loca-

tions, such as on a rickety table or a slanted surface. 

Doing so may result in the unit falling down, causing 

personal injury and/or property damage.


WARNINg

Indicates a potentially hazardous situation which, if mishandled,  

could result in death or serious personal injury. 

CAUTION

Indicates a potentially hazardous situation which, if mishandled,  

could result in moderate or minor personal injury, and/or property damage.

Summary of Contents for MAT-8000

















Reviews: