manualshive.com logo in svg

Artos CS-327, Owner'S Manual

Share
Download
Artos CS-327 Owner'S Manual Download Page 114

114 

 

 

Windows privileges for users 

The CS327 software must have administrator privileges in Windows to work properly.  If the user that 
is currently logged in does not have administrator privileges, the CS327 software will automatically 
log itself in to the user called Artos.  The Artos user must always have administrator privileges.    If 
the CS327 software has to log itself in as the Artos user then only the CS327 software will have 
administrator privileges, all other items in Windows will obey the privileges for the logged in user.   

Machine

 

Software

 

Login

 

 

 

This is the log in screen for the machine software.  
 

Configuring the software to require a log in 

The control can be password protected. To do this a change in the <mtxconfig .xml> is required.  
 

Use Windows File Explorer to locate the mtxcfg.xml  file in C:\Program Files (x86)\Artos 
Engineering\CS327GUI\Config.  If the (x86) directory does not exist then go to C:\Program Files\Artos 
Engineering\CS327GUI\Config. 
 

It is suggested that you make a copy of the existing file before proceeding. Just click copy and paste to 
copy it.  
 
Right click on the original file and then click edit.  If edit is not available from the drop down then 
select open see the next step. 

Summary of Contents for CS-327






































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands