ARRI WCU-4 User Manual Download Page 65

Page: 65 / 79

Appendix

12.2 Screen Messages

Interface

Description

HW Info file could not be

stored. Please insert SD

card.

Insert an SD-card.

License file not valid!

The license file on the SD card

does not correspond to the

WCU-4 serial number.

Used path not found!

Create a valid folder structure on

the SD card.

Disabled during record

Function not available during cam-

era record.

Calibrate lens motors now?

Calibrate lens motors (recom-

mended). If you are sure that

nothing has been changed

since the last calibration, press

CANCEL

Motors calibrating ...

Wait until calibration is finished.

New IRIS Motor! Connect?

Indicates that an iris motor has

been connected to the running

system. Press the

YES

soft button

to assign the motor to the iris slid-

er. Equivalent for zoom and focus

motor.

Warning! Second motor

controller detected! Select

another channel!

The WCU-4 is connected to one

motor controller and has detected

a second motor controller on the

same radio channel. Select anoth-

er radio channel to resolve this sit-

uation.

Summary of Contents for WCU-4
















































































Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands

ARRI WCU-4, User Manual

Search results

Summary of Contents for WCU-4

Reviews:

Related manuals for WCU-4

Brands by name

Popular brands